6640A REV K Norge Washer Parts List

Single lower roller axle (axle - lower rack)

This is the axle ONLY. Wheel is sold separately.

Mounting bracket

The mounting bracket is used to attach the dishwasher to the underside of the counter. The mounting bracket holds the dishwasher in place to keep it from moving during cycles and to keep the dishwasher level. The bracket is made of metal and is approximately 3” in length. The screws are not included with the bracket, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the dishwasher before starting the repair.

Ice maker assembly - 8 cube (icemaker)

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

Drip pan

This round chrome drip pan contains a center hole of approximately four inches wide.

Drawer support rail - left side

This drawer rail supports the left hand side of the sliding drawer.

Door handle

This white handle can be used with both the freezer door and the fresh food door of many refrigerators. Note: As per manufacture this handle includes the mounting block and screw for the top of the handle, If you need the screw for the bottom it must be ordered separately.

Refrigerator ice and water filter (water filter)

Idler pulley assembly

The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.

Dishwasher door gasket with strike - black (door gasket)

This one-piece door gasket provides a water tight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking, tears, or there are gaps in your gasket, you may need to replace the door gasket. This black door gasket is made of rubber, includes a new latch strike plate for the door latch, and is a genuine OEM part.

Retaining ring (Whirlpool dryer retaining ring)

The retaining clip goes onto the end of the roller axle and holds the drum roller on to the axle. If the ring is broken or damaged, you will need to replace it. This is a genuine OEM part and is sold individually.

Charcoal filter (filter)

The charcoal filter is used to eliminate odors while cooking from that air that circulates through the vent. The filter measures approximately 5-inch by 5-inch and is sold individually. This is a genuine OEM part.

Single roller wheel (wheel - lower rack)

Sold Individually.

Upper drum glide (drum glide - top)

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Rear drum bearing kit (shaft & bracket asm)

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Door shelf bar (shelf fixed ff)

This shelf is designed to fit a refrigerator. It connects to the refrigerator door, and is used to hold food and beverage items. It is made of white plastic and is approximately 24 inches wide. The door shelf should snap directly into place. This part will be required if your old shelf is cracked, broken or missing.